Ai uitat parola?


  1. Home
  2. Tutoriale
  • yoshi

  • Mesaje scrise: 4
  • Locatie: Dolj
  • Masina: Astra 2018 B16SHT
  • Status: Offline
  • Cont inregistrat: 17 Oct 2007

  • Mesaj Privat
Da, sunt sigur. Am aflat si ca trebuie sa ajunga pe acel potentiometru 5V. Am verificat si tensiunea de alimentare si tensiunea care se intoarce pentru ECU si este ok, ECU alimenteaza potentiometrul dar nu mai poate interpreta semnalul care se intoarce. Probabil s-a intamplat ceva in interiorul ECU.
Am fost astazi si au pus tech2 pe ea si mi-au confirmat ca semnalul care se intoarce de la senzor si care l-am verificat pana la intrarea in ECU este ok dar la interpretor nu mai ajunge nimic (0V).
In concluzie, galeria este ok si ECU defect. Il voi schimba.
Multumesc mult pentru acest topic si nu numai pentru acesta. Tineti-o tot asa.
Skip ads

  • miha 2011

  • Mesaje scrise: 75
  • Locatie: Dolj
  • Masina: Astra 2003 1598 z1.6exp
  • Status: Offline
  • Cont inregistrat: 23 Nov 2011

  • Mesaj Privat
Multumiri domnului maiandrei,pentru solutia rezolvarii erorii p1113,datorita dumnealui am rezolvat cu succes acest defect,aparut din senin mentionez ca am un astra g 1,6 exp 180200km din 2003,recomand cu incredere aceasta solutie multa bafta tuturor....
  • Merlucius

  • Mesaje scrise: 108
  • Locatie: Bucuresti
  • Masina: Astra 2004 Z16XEP
  • Status: Offline
  • Cont inregistrat: 04 Mar 2008

  • Mesaj Privat
Multumiri lui Marius si din partea mea.
Aceeasi eroare, intai am dat jos blocul Twinport si l-am curatat cu carbusolv, erau ancrasate/colmatate toate canalele de aer de dupa clapete, si clapetele cu un strat de 1 mm de jeg. Dupa operatia de curatare/montare si relipire galerie admisie (zdranganea, vezi topic dedicat pe forum), am montat si eu resistenta pe firul maro. Eroarea a disparut, la fel si fenomenul de lipsa putere in trepte inferioare la peste 2500 rpm.
Hint pt cei care vor sa intervina: demontati tubulatura de admisie aer+debitmetru+suportul filtru aer, astfel aveti acces usor la ramificatia catre potentiometru. Regasiti intr-o tubulatura mai subtire un manunchi de 5 fire: 2 de culoare rosie iar celelalte 3 apartin mufei de interes, respectiv cablurile maro pt un caz si negru/alb pt celalalt caz). Aveti grija la izolarea corespunzatoare, un varnis termic este recomandat.
  • alinutzu18

  • Mesaje scrise: 63
  • Locatie: Prahova
  • Masina: Astra 2004 z1.6xep
  • Status: Offline
  • Cont inregistrat: 25 Mai 2007

  • Mesaj Privat
Salut sa fie asta rezolvarea:


SYSCLEANER
24-12-2012, 08:01
Lot's of time passed but I found the exact solution for twinport error. Actually some german dudes found it and write it on their forum and somebody on my country forums shared and now I'm sharing it with you.

Okey here is the solution:
1.Take out twinport module and clean it.
2.Reach out the sensor at twinport module left side of it.
3.There is two screews which hold this sensor rewind and losen this screews so the sensor can be adjustable.
4.Attach tech 2 your car while every sensor connected (not putted to gether you have still needed to reach 2 screws to calibrate.)
5.Open the voltage check if the port and try to reaching 0.3V by moving sensor and when you reach it rewind 2 screws and fix the position of the sensor.
6.Put together twinport module and intake manifold.
7.Clear if any eror code is existing.


http://www.astraownersnetwo...php/t-145417.html
Skip ads

  • alinutzu18

  • Mesaje scrise: 63
  • Locatie: Prahova
  • Masina: Astra 2004 z1.6xep
  • Status: Offline
  • Cont inregistrat: 25 Mai 2007

  • Mesaj Privat
Intrebare:

Tija clapelor trebuie sa se miste cu motorul oprit? La mine se misca foarte putin la actionarea cu mana. Acelasi lucru a reisit si pe tester, clapetele se deschid doar 14%.

Momentan am rezistenta pusa pe firul maro de aprox 2 ani, dar la un an dupa, mi-a aparut P1112-60, fara martor in bord, dar cu pirdere de putere la turatii mici.

Merci.
  • alinutzu18

  • Mesaje scrise: 63
  • Locatie: Prahova
  • Masina: Astra 2004 z1.6xep
  • Status: Offline
  • Cont inregistrat: 25 Mai 2007

  • Mesaj Privat
Extras din TIS PT Z16 XEP 2003

PDA-System

A PDA system is being used for the first time in Opel petrol engines in the Z 16 XEP-engine. The abbreviation PDA stands for port deactivation.

Advantages from the use of the PDA-system

Increase in the EGR-rate
Extension of the speed range compatible with EGR
Acceleration of the combustion process in the EGR-free low load range
Improvement of smooth-running in the part load range because of high charge carrier mobility
Reduction of fuel consumption
Mode of Operation of the PDA-System

Closing one of the two intake ports per cylinder respectively leads to an increase in charge carrier mobility and therefore to rapid and stable ignition, thus providing the pre-condition for a high EGR-rate.
The use of exhaust gas recirculation then reduces the high combustion speed again to the point where the best possible compromise is reached with regard to combustion noise, untreated exhaust emissions, the knock limit and charge changing losses.
As a result, this produces a reduction in untreated exhaust emissions and a clear saving on fuel.
1. Vacuum unit
2. Injection valve
3. Switching valve
4. Inlet valves




Mode of Operation of the PDA-System

The switching valves, each positioned in the so-called filling port, are opened or closed by a shared actuating rod via a vacuum unit. To do this, the intake pipe has an integrated reservoir which permits a small number of switching operations even if the intake pipe vacuum is slight.
After starting the engine, a sufficient vacuum is normally present within a few seconds to trigger the actuating valve via the engine control unit. When not triggered, the valve opens by spring force, the vacuum unit is ventilated and the valves are opened by restoring springs in the vacuum unit and in the position sensor.
Engine control functions, which are dependent on the valve position, such as the EGR-rate and ignition are controlled via the position sensor dependent on the actual position of the switching valves.
The injection of the fuel takes place via new 2-jet injection valves, whereby one jet respectively supplies the filling and the swirl port.
To ensure that the switched off ports are flushed out, the switching valves have a slight defined leakage - the filling ports are therefore never completely closed.
Closing the switching valve is always demanded by the engine control unit when this will result in advantages with regard to fuel consumption and smooth-running which is generally the case when idling and in the part load range up to about half load and a speed of approx. 3000 rpm. As a consequence of this, the mixture drawn in mainly only flows through the port designed for swirl.
With the switching valve open, i.e. during full load and at high speeds, the mixture also flows through the second port, designed for optimum filling.
1. Vacuum unit
2. Actuating rod
3. Position sensor
4. Switching valves




PDA-System Diagnosis

By the determination of the actual valve position via the position sensor, the vehicle can still be driven without significant restrictions even if malfunctions may have arisen in the switching valve sector.
Therefore, possible customer complaints would be lack of smooth-running during idling or at part load with the valves stuck open or lack of performance at high speed with the valves stuck closed.
Switching valve faults are collected by the engine control unit via the position sensor and stored in the fault memory.
These can then be read off with TECH 2.
  • alinutzu18

  • Mesaje scrise: 63
  • Locatie: Prahova
  • Masina: Astra 2004 z1.6xep
  • Status: Offline
  • Cont inregistrat: 25 Mai 2007

  • Mesaj Privat
Si descrierea pt modeleledin 2004 tot din TIS:

Twinport system

The Twinport system, already in use in the Z 16 XEP DOHC-I petrol engine now also features on the two new members of the 2nd generation DOHC-0 petrol engine series, the Z 10 XEP and Z 14 XEP, albeit in modified form.

Advantages of Twinport

Greater movement of the charge
Combustion stabilisation
Increase in exhaust gas recirculation rate
Reduction in throttle losses
Reduction in fuel consumption
Special features

When the Twinport system is activated (part load), combustion is stabilised because of the increased movement of the charge. Thanks to more efficient combustion, both throttle and wall heat losses can be overcompensated for by the high EGR rates, resulting in a reduction in fuel consumption.
Advanced injection of the fuel onto the closed inlet valve
Stratification of the charge with a richer mixture at the point of ignition at the spark plug.
Inlet manifold with Twinport system

The structure of the inlet manifold is in principle the same for both the Z 10 XEP and Z 14 XEP engines. They only differ in length, which is tailored to the respective engine version (3-cylinder or 4-cylinder).

A vacuum unit actuates the Twinport system; the unit uses a shared actuation rod to close and open the flaps in the inlet ports.


1
Inlet manifold - Z 14 XEP
3
Reverse-transfer lever

2
Vacuum unit
4
Actuation rod




Control valves - Twinport system

At idle when the vehicle speed signal = 0, the control flaps of the Twinport system are closed and the system is active.

As soon as the vehicle drives away, and a driving speed signal is thus present, the control valves are opened or closed, depending on the operating point (load, engine speed).

The engine control unit gives a command to the vacuum unit which in turn closes or opens the control flaps via the actuation rod.

• Service:
So as not to diagnose the Twinport system incorrectly when checking it, the following should be taken into account:

At idle and when the driving speed signal = 0, is when the vehicle is stationary, the control flaps must be closed, the actuation rod is withdrawn and there is a vacuum at the vacuum unit diaphragm.
When the vehicle is being started, the control flaps are opened and after a short while (a few seconds) the control flaps are closed when the vehicle is at idle and the driving speed signal = 0.

Control flaps opened
Control flaps closed


1. Reverse-transfer lever
2. Connection for engine wiring harness
3. Vacuum hose
4. Vacuum tank (engine control unit removed)



The following diagram shows the Twinport system in both activated and deactivated states.


Twinport system inactive with opened control flap
Twinport system active with closed control flap
1. Control flap



Twinport sensor

The Twinport sensor incorporated into the inlet manifold records whether the Twinport flaps are open or closed and sends this message to the engine control unit.

There, the signal of the Twinport sensor is compared with the specified setpoint position.


1. Inlet manifold
2. Twinport sensor
3. Test connection - fuel pressure



• Service:
The control flaps cannot be exchanged or replaced.
  • konve_88

  • Mesaje scrise: 11
  • Locatie: Alta tara
  • Masina: Vectra 1998
  • Status: Offline
  • Cont inregistrat: 08 Oct 2012

  • Mesaj Privat
Am o intrebare pentru maiandrei se poate adapta lucrarea asta și la un motor x16xel? pentru ca am probleme cu potentiometru de la clapeta de acceleratie și anume am un relanti variabil. Dar daca deconectez potentiometru pozitie clapeta de acceleratie motorul merge rotund
Skip ads

  • constantinmarian

  • Mesaje scrise: 39
  • Locatie: Giurgiu
  • Masina: Astra 2009 z16xer
  • Status: Offline
  • Cont inregistrat: 31 Jul 2013

  • Mesaj Privat
rog pe cineva daca imi poate spune care este mufa pe care trebuie sa pun acea rezistenta.motorul este z1.6xep pe opel astra g 2003.stima


  • cmihai

  • Mesaje scrise: 361
  • Locatie: Braila
  • Masina: Zafira 2014 A20DTH
  • Status: Offline
  • Cont inregistrat: 19 Sep 2011

  • Mesaj Privat
astazi am facut si eu up-dateul ca sa zic asa....am montat o rezistenta de 330 ohm pe firul maro....ca si simptome masina mergea foarte rau trepida..pornea greoi....mi-a aparut eroarea 1113 dupa ce am curatat admisia....
  • maiandrei

  • Mesaje scrise: 4,710
  • Locatie: Bucuresti
  • Masina: Insignia 2018 B20DTH
  • Status: Offline
  • Cont inregistrat: 20 Dec 2004

  • Mesaj Privat
Cel mai probabil, problema a fost generata la ultima interventie. Deci in primul rand verifica bine cum ai asamblat la loc.
  • constantinmarian

  • Mesaje scrise: 39
  • Locatie: Giurgiu
  • Masina: Astra 2009 z16xer
  • Status: Offline
  • Cont inregistrat: 31 Jul 2013

  • Mesaj Privat
Salut.aveam aceea eroare p1113 pe rezistenta mare.am inseriat o rezistenta de 560ohm pe firul alb-negru dupa cum s-a discutat,iar rezultatul a fost unul pozitiv.de aproximativ 2 sapt nu s-a mai aprins martorul si nici eroarea nu a mai aparut.multumesc pe aceasta cale domnului maiandrei.stima si respect!
Skip ads

  • Valentinutzul

  • Mesaje scrise: 181
  • Locatie: Arges
  • Masina: Astra 2003 z16xep
  • Status: Offline
  • Cont inregistrat: 04 Feb 2009

  • Mesaj Privat
Salut!am un astra g 16 xep din 2003, de o saptamana masina porneste greu la rece, am pus-o pe tester si imi da aceasta eroape, p1113 , din cauza aceste erori sa fie pornirea grea numai la rece?Multumesc!
  • luly
  • *
  • 39 mesaje
  • din 15 Mar 2016
  • Astra 2004 Z16xep
  • Caras-Severin
  • luly

  • Mesaje scrise: 39
  • Locatie: Caras-Severin
  • Masina: Astra 2004 Z16xep
  • Status: Offline
  • Cont inregistrat: 15 Mar 2016

  • Mesaj Privat
Am si eu un astra h 1.6 z16 xep de 105 cai si am si eu o problema cu ea,i-am curatat clapeta de aer si galeria de admisie si de atunci mi-a aparut masinuta cu cheita cu eroarea 111306.problema e ca la sfarsitul lunii plec la mare si nu stiu de la ce a aparut eroarea asa din senin.cine ma poate ajuta?
  • sec233ast

  • Mesaje scrise: 523
  • Locatie: Salaj
  • Masina: Antara 2012 A22DTH
  • Status: Offline
  • Cont inregistrat: 14 Dec 2007

  • Mesaj Privat
La fel am patit si eu, aveam eroare de amestec sarac care aparea dupa 2-300 de km. Am desfacut adimisia si twinport, le-am curatat (erau obturate canalele de la EGR) la pornire a aparut eroarea P1113 Low Voltage. De sters nu se poate asa ca am montat alt senzor dar tot ramane eroarea. Am observat ca gaurile de prindere sunt de diametru mai mare pentru a putea fi rotit putin. A reusit cineva sa regleze pozitia corect sa nu trebuiasca montata acea rezistenta ?
  • sec233ast

  • Mesaje scrise: 523
  • Locatie: Salaj
  • Masina: Antara 2012 A22DTH
  • Status: Offline
  • Cont inregistrat: 14 Dec 2007

  • Mesaj Privat
Eu am reusit sa rezolv problema cu aceasta eroare, au fost doua cauze. Una a fost lipsa de contact la mufa (aici am remediat cu un ac) si doua a fost pozitia senzorului care s-a modificat odata cu demontarea de pe galerie (am gasit pozitia corecta cu motorul pornit, tot incercand sa sterg eroarea cu OPCOM). In sfarsit am reusit sa repar masina in totalitate, nu mai are nici o eroare si trage foarte bine si liniar. Este ciudat ca la 143000 km sa existe asa uzura pronuntata la clapetele TW, noroc ca am reusit sa fac doua galerii una buna.
  • bodyXasu

  • Mesaje scrise: 27
  • Locatie: Iasi
  • Masina: Astra 2005 Z16XEP
  • Status: Offline
  • Cont inregistrat: 02 Oct 2013

  • Mesaj Privat
Salutare din nou. Am aceeasi problema ca si voi... P1113: Port Deactivation Position Sensor Circuit Low Voltage. Am montat un rezistor de 390 ohm pe firul maro, masina a functionat aproximativ o saptamana fara sa reapara eroare, insa acum, reapare. Ce solutie sa adopt?
  • luly
  • *
  • 39 mesaje
  • din 15 Mar 2016
  • Astra 2004 Z16xep
  • Caras-Severin
  • luly

  • Mesaje scrise: 39
  • Locatie: Caras-Severin
  • Masina: Astra 2004 Z16xep
  • Status: Offline
  • Cont inregistrat: 15 Mar 2016

  • Mesaj Privat
Eu am facut asta aproximativ de 2-3 luni si vad ca nu mi-a mai aparut deloc,dar....am o intrebare.La opel astra h z16xep am vazut cand pun contactul mi se aprind toti martorii din bord inafara de martorul de la lichidul de racire sau cum ii spune.m-am uitat pe youtube la nodelul meu si nu se aprind,e normal?n-am bagat de seama asta desi am masina de 6 luni.in rest termocupla pleclaca.stie cineva daca se aprinde martorul doar cand sesizeaza vre-o problema?
  • Vlady Hodorog

  • Mesaje scrise: 1
  • Locatie: Bihor
  • Masina: Astra 2006 z16xep
  • Status: Offline
  • Cont inregistrat: 17 Aug 2013

  • Mesaj Privat
Am montat si eu pe firu maro o rezistenta ,toate bune martorul mașinã+cheie sã stins da a mai apãrut o eroare la testul cu pedale 111301,
  • romicab

  • Mesaje scrise: 6
  • Locatie: Galati
  • Masina: Astra 2004 Z16XEP
  • Status: Offline
  • Cont inregistrat: 04 Jan 2017

  • Mesaj Privat
Buna seara. Am o Astra G cu motor Z16XEP benzina de 77 KW. De la un timp mi s-a aprins martorul cu cheita si cel cu motorul, iar cateodata cand merg din senin acesti 2 martori incep sa palpaie, motorul nu mai merge rotund, incepe sa tremure si sa piarda putere, toate acestea la accelerare. Opresc masina pe dreapta, inclusiv motorul, iar la repornire motorul merge normal ( cateodata este necesar 2-3 reporniri ). Mai precizez ca de cand am luat masina, luna martie 2016, ventilatorul de AC merge doar la putere maxima. Am fost prin mai multi sau mai putin meseriasi cu testere, care si-au dat cu parerea ba ca este bobina, ba ca sunt bujiile, ba ca este ECU. Am schimbat bujiile si intradevar o zi, doua, motorul a mers impecabil, dupa aceea au revenit simptomele. Am luat bobina de la un cunoscut cu acelasi motor si am pus-o pe a mea, la fel a mers. M-am dus la reprezentanta Opel din Galati, mi-au facut diagnoza ( au reiesit erorile P1113, P0301, P1481 si P1482 ) si mi-au zis ca ECU tb schimbat, dar baiatul de acolo mi-a zis ca se si poate repara la o firma din Bucuresti. Dupa ce am plecat de la reprezentanta m-am dus la un alt service din Galati specializat chipurile printre altele si cu rescrierea programului ECU. Aici mi-au din nou testerul si mi-au zis ca ECU este bun, iar problemele sunt din alta parte. Am plecat de acolo si am sunat la firma care repara ECU-urile, acesta m-a intrebat de erori si a zis ca ECU nu are nimic iar problemele sunt de la admisie si de la clapetele twinport care trebuiesc curatate. A doua zi m-am dus la un alt service, le-am explicat despre ce este vorba, acestia mi-au pus testerul si mi-au zis ca problema este ECU si tb altul. Acum nu stiu ce sa mai fac, daca cumpar ECU si nu acesta este vinovatul? Dupa dumneavoastra, care ar fi cauza? Va multumesc mult.
Skip ads

  1. Home
  2. Tutoriale

Intra in ClubOpel!

check Cea mai mare comunitate Opel
check Intalniri locale
check Skip Ads
check Vinzi/Cumperi
check Gratuit pe viata




CO+FB CO+FB CO+YT CO+IG CO+TWTR